Check out part 3 of my review of Pat’s Minion 260 H-Quad – covering its flight and my final thoughts.

The kit contains:
– 1x Mini H-Quad Top Plate 1mm CF
– 1x Mini H-Quad Bottom Plate 2mm CF
– 2x Mini H-Quad Arms 2.5mm CF
– 1x Mini H-Quad Camera Mount 1.5mm CF
– 1x Mini H-Quad Fasteners Pack

$110 for 5″ prop version
$115 for 6″ prop version

It weighs in at 85g for the 5″ prop version.

Pat’s Mini H Quad Website

RC Groups Forum Post

Join the Club!

Check out part 2 of my review of Pat’s Minion 260 H-Quad. It weighs in at 85g for the 5″ prop version and is made of carbon fiber.

The kit contains:
– 1x Mini H-Quad Top Plate 1mm CF
– 1x Mini H-Quad Bottom Plate 2mm CF
– 2x Mini H-Quad Arms 2.5mm CF
– 1x Mini H-Quad Camera Mount 1.5mm CF
– 1x Mini H-Quad Fasteners Pack

$110 for 5″ prop version
$115 for 6″ prop version

Pat’s Mini H Quad Website

RC Groups Forum Post

Join the Club!

Check out part 1 of my review of Pat’s Minion 260 H-Quad.

The kit contains:
– 1x Mini H-Quad Top Plate 1mm CF
– 1x Mini H-Quad Bottom Plate 2mm CF
– 2x Mini H-Quad Arms 2.5mm CF
– 1x Mini H-Quad Camera Mount 1.5mm CF
– 1x Mini H-Quad Fasteners Pack

It weighs in at 85g for the 5″ prop version and is made of carbon fiber.

$110 for 5″ prop version
$115 for 6″ prop version

Pat’s Mini H Quad Website

RC Groups Forum Post

Just a little sneak peek at the Minion Mini H Quad I built for my next review…

– Airbot 2300kv motors
– Blue Series 12amp ESCs
– 3s – 1300mah lipo
– GemFan 5030 / HQ5040
– Fatshark 250mw VTx
– PZ0420 FPV Cam
– Mobius Action Cam

I am happy to announce that I will be reviewing the Minion Mini H Quad from patsminihquad.com.

The Minion is only 218mm diagonal MTM for the 5″ prop version (260mm for the 6″ prop version, 172mm wide and 129mm long MTM and weighs 85g. The kit contains the following parts:

– 1x Mini H-Quad Top Plate 1mm CF
– 1x Mini H-Quad Bottom Plate 2mm CF
– 2x Mini H-Quad Arms 2.5mm CF
– 1x Mini H-Quad Camera Mount 1.5mm CF
– 1x Mini H-Quad Fasteners Pack

I will be reviewing the Minion 260, which is the version that supports 6″ props. I am hoping to have part 1 wrapped up sometime next week – so keep checking back. A special thanks goes out to Patrizio Gualtieri for providing the frame to the MQC for review.

Thanks again for all the support!

Without further adieu, here is part 3 of my review of the Thrust UAV HyperLite 275. Special thanks to E.J. Duarte from Thrust UAV for sending me out this frame to review.

Company Link: Thrust UAV

My Setup:
T-Motor 12amp ESCs
T-motor 2206 2000kv motors
Naze32
4s – 1300 mah lipo (~5 minutes flight time)
Fatshark 250mw VTx
Fatshark CMOS cam
Spektrum AR6210 receiver

 

I review the HyperLite 275 made by Thrust UAV. This is part 2 of the review covering the build. Enjoy!

Part 1 of my 3 part review of the Thrust UAV HyperLite 275.